Common failures and solutions of cone crusher Sanme. Fault 1: The oil pressure in the oil pipes before and after the filter is not the same Cause of failure: clogged filter Troubleshooting methods: When the oil pressure difference exceeds 004MPa, the filter must be cleaned, so that the oil does not pass through the ground filter, and then the filter is removed for cleaning, so that the oil is ...
[email protected]
Get Quick
Quote
If you have any problems or questions about our products or need our support and assistance, please contact us and you will be replied within 24 hours. We promise we will never reveal your information to the third party. Thank you!
Oct 28, 2020 8. The oil flow indicator shows that the oil is cut off. The oil pump may be in failure. The oil pump should be repaired or replaced. In winter, if the oil temperature is too low, the oil can be heated to ensure normal lubrication for jaw crusher.
39 Item Part No. Image 1 DE1007 2 DE6000 3 DE6004 4 DE6015 5 DE6006 DE5024 6 DE6007 7 DE0027 tagout)
Cone crusher oil pump pipe Mining Machinery Co Ltd. cone crusher oil pump pipe How to prolong the cone crusher service life First problem is the unbalanced pressure in oil pipe between filtersthe possible reasons may be there is jam in the filterthe solution to cone crusher filter jam is that clean the filter when the oil pressure difference over this condition we should make oil not pass ...
• CRUSHER OPTIONS Cogged belt drive Longer remote cables (100’, 150’, 200’) Hopper extention Hopper extention with overflow chute Cold climate oil recirculating kit Crusher automation package Hydraulic cone brake KODIAK+ CONE CRUSHERS Specification Sheet *Crushers shown without standard sheave
system and the crusher are protected with this additional security measure. Reliability The Raptor XL1100 cone crusher has been designed to be the most reliable high performance cone crusher available. Spiral Bevel Gears, Fail-Safe Hydraulics, Fault Protec-tion Automation, Specialized Bronze Metallurgy and a High Open Area
Cone Crusher Material is fed into the crusher cavity and processed by the eccentric rotating action of the inner cone against the outer cone. Work can be reduced to a diameter ranging from 50 mm to 100 mm. Impact Crusher As indicated by its name, this machine crushes ore through impact, and steadily reduces the size of the crushed
KODIAK PLUS CONE CRUSHERS Specification Sheet *Crushers shown without standard sheave • CRUSHER High efficiency roller bearing design Remote Close Side Setting (CSS) adjustment Digital read out setting control Patented brass bowl threads Patented no creep bowl clamp Patented mechanical crusher duty cone brake K200+, K300+, K400+ Hydraulic Cone Brake Std on K500+ …
The coal hammer crusher is the key equipment for crushing large raw coal in the underground coal. The machine is an important part of the raw coal transportation system. The common problems are design Defects, installation, debugging and maintenance problems, parts wear and deformation, movable cone unbalance, rotor rub-impact, shaft ...
VSI series crusher are featured in high reliability,less maintenance and economic operation cost over competitors,all the benefits are from cascade feeding,deep rotor,full feed flow centralization,inner air flow cycling,heavy duty hearings and oil lubrication systems.
May 22, 2021 Today, I will introduce the operation method of quartz powder mill.(1) Start Before operation, you must check item by item according to the inspection content, and make preparations for driving only after confirming that there is no fault. Start the oil pump first and check whether the oil flow at the lubrication point and the […]
Jun 18, 2021 Common Faults and Cause Analysis of Cone Crusher. The large and small bevel gears are worn and broken teeth. The oil quality of the lubricating oil has deteriorated. The crusher often vibrates. There is a violent impact sound, the support sleeve jumps up, and then it works normally. There is a cracking sound when crushing ore.
When the cone crushing motorized cone rotates at a high speed beyond the normal speed, the phenomenon of flying often occurs. After the “speeding” fault, the revolution of the moving cone was too high, which would cause the oil temperature of the lubricating oil to rise, but the oil pressure to decrease; the current of the motor increased.
Aug 01, 2019 The oil indicator shows no oil flow, but the oil pressure is lower than 0.5 MPa. Reason : the oil temperature is too low; the switch of oil is turning off; the oil pump doesn’t work well. Solution : heat the oil; turn on the oil switch; turn off the crusher and change the oil pump.
Nov 25, 2019 The reason for oil leakage in cone crusher. The reasons for oil leakage in cone crusher 1. Faults of the sealing system. During the crushing process, the worn condition of the sealing ring between the shaft frame and the mainframe should be checked. After a long term of use, this part of cone crusher may be worn and the original flexibility of the sealing ring would be reduced. 2.
HPT Cone Crusher - Raymond mill. cone crusher oil flow indicator is no oil flow, oil pump runs but oil is lower than 0.05Mpa. Fault Analysis 1, the oil temperature is low, 2, oil switch is not a good... More details Get Price
Jul 18, 2015 The fact that a crusher has this flow switch in the oil circuit should not become an excuse for the operator not monitoring the line pressure. A switch can fail. Also conditions may be present where the pressure is slowly dropping because of a slow leak. If it is caught early a lot of down time or damage to the equipment can be prevented.
Copyright © 2021.Henan Exodus Machinery Co., ltd. All rights reserved.
